"Can we bend plasterboard round that?" depends on the radius, the board thickness, whether you wet it and how you frame it. This guide collects the minimum bending radius figures that manufacturers actually publish and sets out which method suits which radius. For a broader comparison of the four ways to build a curve, see our guide to curved drywall methods.
The short answer:
- Standard 12.5 mm plasterboard only bends to large radii on site: published minimums run from 1500 mm to about 3000 mm dry, depending on the manufacturer.
- Thin flexible board (6 to 6.5 mm) goes much tighter: roughly 900 to 1000 mm dry, and down to 300 mm wet for at least one product.
- Below about 250 to 300 mm, no on-site method in the data below gets you there reliably. That is where factory-grooved, pre-formed profiles take over.
Why plasterboard has a minimum radius
Plasterboard is a gypsum core held between two paper liners. When you bend it, the liner on the outside of the curve is stretched and the liner on the inside is squeezed. The gypsum core between them is brittle and takes very little strain before it cracks.
The strain at the face grows with board thickness and shrinks with radius. As a rule of thumb from simple beam geometry, it is roughly the board thickness divided by twice the radius. Halve the thickness and you can roughly halve the radius for the same strain. That is why 6 mm board bends so much tighter than 12.5 mm board, and why manufacturers publish separate figures for each thickness.
Go past the limit and either the face paper tears on the tension side or the core cracks across its width, sometimes only showing after jointing as a hairline crack along a stud line.
Published minimum bending radii
These figures come from manufacturer datasheets and technical notes. Each assumes that manufacturer's own board, framing and fixing method, and values vary by product, region and edition, so always check the current datasheet for your board before setting out.
| Manufacturer and board | Thickness | Minimum radius, dry | Minimum radius, wet | Notes |
|---|---|---|---|---|
| Knauf Formplatte GKB (Germany) | 6.5 mm | 1000 mm | 300 mm | Product datasheet K7124, 10/2025 |
| Siniat GTEC Contour Board (UK) | 6 mm | 900 mm | 600 mm | Studs and joists at 300 mm maximum centres |
| Gyprock Flexible (Australia / NZ) | 2 x 6.5 mm | 250 mm convex, 450 mm concave | Not stated | Two layers to a 13 mm lining |
| GIB plasterboard (New Zealand) | 10 mm | 1200 mm | 1000 mm | Sheets fixed horizontally |
| GIB plasterboard (New Zealand) | 13 mm | 1500 mm | 1200 mm | Sheets fixed horizontally |
| National Gypsum (USA) | 1/4 inch (6.4 mm) | 5 ft (about 1.5 m) | Only for very tight radii | General guidance |
| National Gypsum (USA) | 1/2 inch (12.7 mm) | 10 ft (about 3 m) | Only for very tight radii | General guidance |
A few things stand out:
- For 12.5 to 13 mm board, the sources disagree by a factor of two. GIB gives 1500 mm dry for its 13 mm board; National Gypsum gives 10 feet (about 3 m) for 1/2 inch board. Treat anything under about 1.5 metres as outside what standard board is designed to do on site.
- Wetting buys you a lot on thin board, less on thick board. Knauf's 6.5 mm board goes from 1000 mm dry to 300 mm wet. GIB's 13 mm board only goes from 1500 mm to 1200 mm.
- The radius is a system figure. Siniat reaches 900 mm with the board fixed horizontally on deep flange flex track, C-studs at 200 mm centres and flat strap behind the horizontal joints.
Dry bending versus wet bending
Dry bending is the default: the framing pulls the board into shape, with no waiting and no loss of strength. If your radius is above the dry figure for your board, bend it dry.
Wet bending softens the paper and lets the core take more strain. GIB's published method is to apply water with a paint roller to both sides, about 40 mL/m², and allow around 10 minutes before bending. National Gypsum notes that wetting is only needed on extremely tight radii, and that low temperature and humidity reduce flexibility. The board must dry before jointing and is weaker while wet. GIB excludes some boards from wet bending, advises against curving its thickest and high-density boards, and found a typical fitting time of 30 to 40 minutes per board.
Layering thin boards
A single 6 mm layer is not a finished wall, so thin board usually goes on in two layers, building up close to a standard 12.5 or 13 mm lining. Gyprock states that its Flexible board is typically installed in two layers for a 13 mm lining, and gives the 250 mm convex and 450 mm concave figures for that build-up.
It costs a second round of fixing and staggered joints, but over a long curved wall it is still the most practical route to a smooth, continuous surface.
Kerfing and V-grooving
Cutting into the back of the board removes core where it would be squeezed, so the board folds rather than bends. Kerfing on site (saw cuts through the core, stopping at the face paper) works for one-off pieces, but every cut matters: too far apart and the curve looks faceted, too deep and the paper tears.
V-grooving is the same principle done by machine. The grooves are cut at a fixed angle and spacing, so the board folds into a true radius with the face paper intact. This is how factory pre-formed profiles reach radii that no on-site method in the table gets near.
Stud and track spacing on curves
The tighter the curve, the closer the support, or the board spans flat between fixings and the curve turns into facets. GIB publishes this table:
| Wall or ceiling radius | Maximum stud, batten or joist spacing (GIB) |
|---|---|
| 900 to 1200 mm | 200 mm |
| 1200 to 3000 mm | 300 mm |
| 3000 to 4000 mm | 400 mm |
| Over 4000 mm | 600 mm (450 mm for 10 mm board in ceilings) |
Siniat gives 300 mm maximum centres for Contour Board, and 200 mm at its 900 mm minimum. GIB fixes sheets horizontally and carries each sheet at least 300 mm past the end of the curve.
Convex versus concave
On a convex (outside) curve the board wraps round the studs and sits tight. On a concave (inside) curve it wants to spring away from the framing between fixings. Gyprock's figures show the difference: 250 mm convex against 450 mm concave for the same build-up. GIB notes that lining the inside of a curve takes more labour and the board must be curved before installation; its method fixes from one end on an outside curve and from the centre outwards on an inside curve.
Which method for which radius
- Above about 1.5 to 3 metres: standard 12.5 mm board, bent dry on correctly spaced framing. Check your manufacturer's figure.
- Roughly 1 metre to 1.5 metres: thin flexible board in two layers, dry. Or thicker board wet, if the manufacturer allows it and the programme can wait.
- Roughly 300 mm to 1 metre: thin flexible board, often wet. Expect slow work and close framing.
- Below about 300 mm: soft corners, bulkhead noses, column heads and small arches. Kerf a one-off; use a pre-formed profile for anything that repeats.
Where a factory-curved profile fits
BendBoard profiles are made from standard 12.5 mm plasterboard. The back is machined with closely spaced V-grooves and the board is bent to the required radius in the factory. The standard curved profiles have an R100 radius, which is 100 mm, well below the tightest on-site figure in the table above:
- BendBoard 010 joins a 100 mm upstand and a 150 mm horizontal leg with a 90° bend at R100, for rounded ceiling-to-wall and bulkhead corners.
- BendBoard 005 is a 265.9 mm flat base running into an R100 arc with a 129.1 mm arc length, for bulkhead noses and column heads.
- BendBoard 013 is a one-piece semicircular arch profile with two 150 mm legs and a 290.2 mm arc length, for arches over doorways and niches.
Other radii, arc lengths and leg lengths are made to measure. The pieces fix to standard metal framing, need no wetting or formwork, and are identical from piece to piece.
Where it does not fit: a long curved wall with a radius of several metres. There, flexible board or standard board bent dry is simpler, cheaper and gives one continuous surface. Pre-formed profiles also need ordering ahead and a signed-off section.
If your drawing has a tight radius that repeats, send us the section and quantities through the quote form.
FAQ
What is the minimum bending radius for 12.5 mm plasterboard?
Published figures range from 1500 mm (GIB, 13 mm board, dry) to about 3000 mm (National Gypsum, 1/2 inch board). Wetting helps a little: GIB gives 1200 mm wet for its 13 mm board. Use the datasheet figure for the board you are actually fixing.
How tight can you bend flexible plasterboard?
Thin flexible boards of 6 to 6.5 mm typically bend to about 900 to 1000 mm dry. Knauf's Formplatte GKB 6.5 mm is listed at 300 mm wet, and Siniat's 6 mm GTEC Contour Board at 600 mm after wetting. Gyprock quotes 250 mm convex and 450 mm concave for two layers of its 6.5 mm Flexible board.
Should I wet plasterboard before bending it?
Only if the radius is tighter than the dry figure for your board and the manufacturer publishes a wet figure. Wetting adds drying time before jointing and weakens the board while it is damp. On thick board the gain is small, so it is usually better to switch to thin flexible board in two layers.
What stud spacing do I need for a curved plasterboard wall?
Closer than for a flat wall. GIB specifies 200 mm centres for radii of 900 to 1200 mm, 300 mm up to 3000 mm, 400 mm up to 4000 mm and 600 mm above that. Siniat gives 300 mm maximum for its Contour Board and 200 mm at the 900 mm minimum radius.
Is a concave curve harder than a convex one?
Yes. On a concave curve the board tries to spring off the framing, so it must be pre-curved and fixed from the centre outwards. Gyprock's figures for the same build-up are 250 mm convex against 450 mm concave, and GIB notes that lining the inside of a curve takes more labour.
What radius do BendBoard profiles come in?
The standard curved profiles, BendBoard 005 and 010, have an R100 (100 mm) radius, and BendBoard 013 is a one-piece semicircular arch. They are made from V-grooved 12.5 mm plasterboard, and other radii, arc lengths and leg lengths are made to measure.

