There are four common ways to build curved drywall. None of them is right for every job. This guide compares them honestly, including where our own product, pre-formed plasterboard, is not the best choice.
The short answer:
- Large, gentle curves on long walls: bend standard or flexible board on site.
- Tight radii, repeated details and anything that has to match from piece to piece (soft corners, column heads, curved bulkheads, arches): pre-formed profiles save the most site work.
- One-off small pieces: kerfing is still a reasonable fallback.
Method 1: Bending standard board (dry or wet)
How it works: Standard plasterboard has some give. For large radii, you can bend it dry onto curved framing. For tighter radii, crews dampen the side of the board that goes on the inside of the curve, let the water soak in, bend the board onto the framing or a template, and leave it to dry before jointing.
What it costs you on site:
- Waiting. Wet board has to dry before you can joint and finish it, so the detail holds up the follow-on trades.
- A template or tight framing. For anything below a generous radius you need closely spaced studs or a former to hold the shape while the board dries.
- Risk. Push it too far and the face paper cracks or the core breaks. That board goes in the skip and you start again.
Minimum radius: This depends on board type and thickness. Always check your board manufacturer's bending table. Thick standard board only bends to fairly large radii, even when wet.
Best for: Long, gently curved walls with a large radius, where the board bends dry and you're not waiting on anything.
Method 2: Kerfing
How it works: You cut a series of parallel saw cuts across the back of the board, through the core but not through the face paper. The board then folds along the cuts into a curve.
What it costs you on site:
- Labour per piece. Every cut is marked and made by hand. The spacing and depth decide whether you get a smooth curve or a faceted one.
- Consistency. Two people kerfing two pieces rarely get the same result. On a run of matching details, it shows.
- A weaker piece. Over-cut and the face paper tears. The cut-back core also needs more filling to get a smooth finish.
Best for: A one-off small curve when you have no other option on the day. Kerfing works, but it doesn't scale well.
Method 3: Flexible (thin) bendable board
How it works: Thinner, purpose-made bendable boards are fixed in two or more layers to curved framing, building up to the required thickness. Some can be bent dry to quite tight radii, and tighter still when dampened. Check the manufacturer's data.
What it costs you on site:
- Double handling. Two layers means two rounds of fixing, more screws and staggered joints.
- Special stock. It's another board type to order, store and keep track of on site.
- Framing. Curved tracks and closer stud spacing are still needed.
Best for: Long curved walls and large barrel ceilings where you need a continuous, smooth surface over a big area. This is where flexible board is hard to beat.
Method 4: Pre-formed plasterboard profiles
How it works: The shaping happens in the factory, not on site. Standard 12.5 mm plasterboard is machined with closely spaced V-grooves on the back and then bent into the required radius. It arrives as a finished piece: a curve with straight legs on either side, or a complete arch with both legs. On site, the crew screws it to standard metal framing for ceilings and partitions, and then joints the seams.
At BendBoard, the standard curved profiles are:
- BendBoard 005: a soft R100 transition with a 265.9 mm base and a 129.1 mm arc.
- BendBoard 010: an R100 curve between a 100 mm upstand and a 150 mm horizontal leg.
- BendBoard 013: a semicircular arch made in one piece, with two 150 mm legs.
Radius, arc length and leg lengths can be made to suit the project.
What it saves you on site:
- No wetting, no formwork, no flexible board. The curve is already there.
- Every piece is the same. Ten column heads or forty metres of soft corner come out identical because they're made on the same machine setup.
- Fewer joints in the curve itself. The curved part is one piece, so the joints sit in the straight sections where they are easier to finish.
What it doesn't do (honestly):
- It has to be ordered in advance. It's a made-to-order product, so it needs to be in your programme, not decided on the morning.
- It isn't the answer for very large radii. For a long, gently curved wall, bending standard or flexible board on site is often simpler and cheaper.
- The geometry is fixed when you order. If the drawing changes after production, the piece won't adapt the way a site-bent board can. Get the section signed off first.
Best for: Tight radii (soft corners, column heads, curved bulkheads), arches, and any detail that repeats across a project and has to look the same every time.
Side-by-side comparison
| Bending standard board | Kerfing | Flexible board | Pre-formed profiles | |
|---|---|---|---|---|
| Typical use | Large-radius walls | One-off small curves | Long curved walls, barrel ceilings | Soft corners, column heads, bulkheads, arches |
| Shaping done | On site | On site | On site | In the factory |
| Waiting on site | Yes, if wetted | No | Sometimes, if dampened | No |
| Template / formwork | Often, for tight radii | Sometimes | Curved framing | No (standard framing) |
| Same result piece to piece | Depends on the crew | Hard to repeat | Good over large areas | Identical pieces |
| Planning needed | Low | Low | Medium (special stock) | High (order ahead) |
| Main risk | Cracked paper, drying time | Faceting, torn paper | Extra layers and fixing | Late changes to the drawing |
How to choose: a quick checklist
Ask these four questions about the curve on your drawing:
- How tight is the radius? If it's large enough to bend standard board dry, do that. The tighter it gets, the more pre-formed makes sense.
- How many times does it repeat? One curve on one wall: build it on site. The same soft corner on every bulkhead in a store: have it made.
- Does it have to match? Light coves, shadow gaps and curved bulkheads in retail and hotel interiors are inspected closely. Identical pieces make the finish easier.
- Is the drawing final? Pre-formed profiles reward early decisions. If the design is still moving, wait or build that part on site.
Installing a pre-formed curved profile: the outline
Each BendBoard product comes with an installation detail drawing. In outline:
- Set out and build the framing with standard metal sections for the ceiling or partition, following the detail drawing for the profile.
- Offer up the profile and check alignment against the framing and adjacent boards.
- Screw it to the framing.
- Butt the next piece along the run. Because each piece has the same geometry, the curve lines up from one piece to the next.
- Joint and finish the seams and the junctions with the flat board as normal.
Need the detail drawing for a specific profile? Request the technical file from the product page.
FAQ
Can you bend 12.5 mm plasterboard?
Yes, but on site only to large radii, even when wet. Check your board manufacturer's bending table. For tight radii, either use thin flexible board in layers or use 12.5 mm board that has been V-grooved and bent in the factory.
What radius do BendBoard curved profiles come in?
The standard curved profiles have an R100 radius (BendBoard 005 and 010), and the arch profile (BendBoard 013) is a one-piece semicircle. Radius, arc length and leg lengths can be made to suit your project.
Do pre-formed profiles need special framing?
No. They fix directly to standard metal framing for suspended ceilings and partitions.
What do you need for a quote?
The profile code or a section drawing, approximate quantities, the project location and the required delivery date.

