Skip to content

Plasterboard channels and light coves

U-shaped plasterboard channels for concealed lighting, curtain tracks and service runs. Because each channel is folded in one piece, the internal dimension stays constant along its length, which makes fitting luminaires and tracks easy. Deep, shallow, asymmetric and double-return versions are used as ceiling light coves, wall niches and cable channels. Internal width and depth are made to suit your project.

Profiles

Plasterboard light coves and curtain recesses: a guide to U-channels

How a light cove is usually built, and what a folded channel changes

On most jobs a plasterboard light cove is built on site from strips of board. The soffit, face and return are cut separately and screwed to the framing, every arris gets a corner bead or corner tape, and the corners are filled in several coats. Curtain pelmets and service boxings are built the same way. The longer the run, the harder it is to keep the internal dimension the same from end to end.

BendBoard channel profiles are folded into a U in the factory. The back of 12.5 mm plasterboard is V-grooved, the board is folded in one piece and the face paper runs continuously round each corner. Internal width and depth stay constant along the whole length, so LED strips, luminaires and curtain tracks sit in the same space at every point.

Four sections: BendBoard 006, 007, 011 and 012

BendBoard 006 is a symmetrical U-channel with a 300 mm base, two 70 mm side legs and a 25 × 50 mm return on each edge. The double return narrows the opening from both sides, hides the LED source in a wide light cove and leaves a shadow line on either side.

BendBoard 007 is deep and narrow: 150 mm deep with an inner width of 55 mm. It suits curtain recesses set into a suspended ceiling and slim concealed lighting slots.

BendBoard 011 is asymmetric, with a 250 mm long leg, a 250 mm base and a 70 mm short leg. It suits coves and curtain pockets that stay closed on one side only, and bulkheads that link two ceiling levels.

BendBoard 012 is a plain symmetrical channel, 100 mm deep and 200 mm wide, without returns. It works as a recess for linear luminaires, an enclosed service channel or a simple wall niche. On every model, internal width and depth can be made to suit the project.

Concealed lighting, curtain pelmets and service runs

For a perimeter light cove in a ceiling, the usual choices are BendBoard 006 with its returns, or BendBoard 011 where only one side needs to be closed. To recess a curtain track into a plasterboard ceiling, the deep, narrow BendBoard 007 keeps the track out of sight, and the asymmetric BendBoard 011 works where the curtain runs against a wall. BendBoard 012 covers linear luminaires, cable runs and wall niches.

The channels screw to standard metal framing for suspended ceilings and partitions, with no special carrier. Because the corners are part of the board, joints fall where the channel meets the flat ceiling or wall and are finished as normal. Each product comes with an installation detail drawing.

Pre-formed channel or site-built cove?

A pre-formed channel saves the most site work on long runs, where the same section repeats from room to room, and where a luminaire or track with fixed dimensions has to fit inside. For a single short pelmet, or a detail whose dimensions keep changing on site, building it from strips of board may be all you need.

Channels are made to order and the internal dimension is fixed in production. Confirm the LED profile, luminaire or curtain track dimensions and get the section signed off before ordering.

How do you build a light cove in a plasterboard ceiling?
Either from strips of board fixed to framing on site, with corner beads and filling at every arris, or with a pre-formed channel that arrives folded in one piece. BendBoard 006 forms a wide cove with returns on both sides; BendBoard 011 is for coves that are closed on one side only.
How do you recess a curtain track into the ceiling?
Form a pocket in the suspended ceiling that is deep enough to hide the track. BendBoard 007, 150 mm deep with a 55 mm inner width, is made for this. Other internal dimensions are made to suit the project.
Can the channel be made to fit a specific luminaire or track?
Yes. Internal width and depth are made to suit the project. Send the luminaire or track dimensions together with a section drawing.
Do the channels need special framing?
No. They fix to the standard metal framing used for suspended ceilings and partitions, and each product comes with an installation detail drawing.
What do you need for a quote?
The profile code or a section drawing, approximate lengths, the project location and the required delivery date.

Get a quick quote for your project.

Share your drawings or dimensions and we will work out the right profile, price and delivery together.